Phasellus ultrices ligula vitae velit aliquam porta. Integer id vehicula velit.
You may unsubscribe at any time using the unsubscribe link in the digest email.
Checking your sprinkler package at the end of the season is key to ensuring you will be ready for next year. With all of the hard work that needs to be done and the matters that require your consideration during harvest, you might be tempted to put off the inspection of your farm irrigation equipment. However, this is a good time to detect potential issues such as leaks, plugged nozzles or pressure regulators, wrong nozzle size, or damaged/worn-out sprinklers. These suggestions from Senninger® give you a quick overview of the things you should consider.
Find a copy of your sprinkler package chart. This contains the location of all sprinklers and pressure regulators along the center pivot. It will also include detailed information for each sprinkler’s nozzle size or flow rate. You’ll need it a little later when you’re walking along your pivot verifying sprinkler location and noting potential issues.
Check the main pipe running from the well to the pivot itself for any potential leaks. Next, remove the sand trap on your pivot and flush the entire system for several minutes. (Make sure the system is not under pressure when you remove the sand trap!) This will flush out any debris or foreign materials that may plug the sprinkler heads or pressure regulators.
Sprinklers on the first few spans are particularly prone to plugging due to their smaller nozzles size, so we recommend a good system flush at least once a year.
Using a pressure gauge, verify your pressure at the pump, pivot point, and at the end of the pivot. Make sure you operate the center pivot system at the design pressure.
Pressure should be at least 5 psi above the pressure regulator rating. If you have a 10 psi pressure regulator, your pressure gauge should read a minimum of 15 psi. Compare the numbers to the design pressure in your sprinkler package chart to make sure everything matches.
Note: It’s best to check pressure with the pivot parked in the same location!
Sometimes, farmers discover that the nozzles along each span do not correspond with what the printout indicates. This is why it’s important to keep your chart on hand.
Check the system flow rates by comparing each sprinkler to the corresponding outlet on the chart. Each sprinkler’s nozzle and flow rate should match the number on the sprinkler package chart. If the nozzles are wrong, you may be over or under watering.
If you have a flow meter, verify that it’s taking the correct measurements. Solving issues like a flow meter not receiving a signal or unstable flow rates might require a little detective work on your part using your flow meter installation and troubleshooting guide.
Visually inspect all sprinklers for potential damage, lost parts, and for consistency and uniformity in their distribution patterns. Assure that sprinkler overlap is sufficient.
Disassemble any sprinklers with poor distribution patterns or overlap, and check for plugging or defective parts. Sprinklers can wear out and will stop rotating – or rotate out of control. Check sprinkler deflector pads to ensure they do not have a build-up of materials that could affect the distribution pattern or flow rate. You might also notice kinked or damaged drop hoses that need fixing.
Sprinkler issues can result in extra water being applied is some areas and insufficient water being applied in others. This affects water application uniformity and can reduce yields.
According to the University of Nebraska-Lincoln, depending on the location of the problem along the pivot pipeline, the economic impact of a single sprinkler problem can be significant in the amount of yield reduction it causes. This is especially true for sprinklers on the outer 30% of the center pivot system.
Hopefully, you won’t notice any runoff or a lack of uniformity while inspecting your sprinklers, but if you do:
Evaluating farm irrigation equipment at the end of every growing season is just as essential as any maintenance and upkeep you do for other farm machinery and equipment. The less you neglect, the more you will gain. Contact your local Valley dealer and ask for more information on winterization today.
Did you enjoy this article? You may enjoy these, too!
An Ounce of Prevention For Your Irrigation Equipment
3 Rules of Thumb to Remember When Inspecting Your Irrigation Sprinkler Package
5 Life Hacks For Effective Sprinkler Package Design
Founded in 1963, Senninger is one of the world’s leading manufacturers of agricultural irrigation products with a focus on sprinklers, spray nozzles and pressure regulators. Senninger provides solutions that can be found in agricultural, horticultural and industrial applications. Senninger products are made in the United States and sold worldwide via their professional dealer network.
Senninger has recently joined the Hunter Industries family of companies. Hunter Industries is global manufacturer of products for the irrigation, landscape lighting, and custom manufacturing sectors. Founded in 1981, the family-owned company offers more than 1,000 products including a complete spectrum of water-efficient solutions for residential and commercial irrigation systems. Hunter’s core mission always has and always will remain the same: to produce innovative products of the highest quality and back them with unwavering customer support. To learn more, visit senninger.com.
28800 Ida St
Valley, NE 68064 USA
© 2020 Valmont Industries, Inc.